swiing® revival rear wheel axle set (cast hub) Leleu

Sliding bush fork original | Puch

Manufacturer: Made in Italy · Material: Plastic · Surface: raw · Color: white · Ø inside: 23 mm · Ø outside: 27 mm · Total length: 30 mm

swiing® revival bottom bracket bushing nylon | Puch Maxi, X30 Sport, Velux, NG-2AH

Ø Bundle: 24.1 mm · Manufacturer: swiing® revival parts · Material: Nylon · Surface: blank · Bearing type: Plain bearing · Color: black · Ø inside: 16.2 mm · Ø outside: 20.2 mm · Total length: 19 mm · Puch spare part no.: 349.1.42.005.1

NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard · Ø inside: 12 mm · Bearing type: Deep groove ball bearing · Ø outside: 28 mm · Width: 8 mm · Ball bearing closed: Yes

swiing® revival rear wheel spacer tube L=70 mm | Puch Maxi

Nominal diameter: 12 mm · Manufacturer: swiing® revival parts · Ø inside: 12.5 mm · Ø outside: 16 mm · Total length: 70 mm · Puch spare part no.: 349.5.41.826.1

swiing® revival wheel axle set M12x1 x 185 cast rear wheel galvanized | Puch

Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Thread type: MF12x1 (fine pitch thread) · Width across flats SW: 19 mm · Ø shaft: 11.9 mm · Ø outside: 11.8 mm · Shank length: 100 mm · Total length: 185 mm · Thread length: 26 mm · Thread length: 52.5 mm

swiing® revival rear brake anchor plate | Puch Maxi S

Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Ø outside: 91 mm · Brake lever length (lever length): 55 mm · Total length: 187 mm · Cranking (offset): 8 mm

swiing® ingenious brake shoes Ø 80 x 18 Racing slotted

Manufacturer: swiing® ingenious parts · Number of springs: 2 pcs · Springs included: Yes · Color: silver · Ø locating bolt: 10 mm · Slotted: Yes · Ø drum: 80 mm · Width: 18 mm · Area of application: Racing

swiing® ingenious wheel axle cast hub front Ø 29 mm conversion kit ball bearings | Puch

Manufacturer: swiing® ingenious parts · Material: Steel · Surface: blue galvanized · Thread type: MF12x1 (fine pitch thread) · Width across flats SW: 19 mm · Ø shaft: 11.95 mm · Ø inside: 12 mm · Ø outside: 29.02 mm · Shank length: 74.5 mm · Ball bearing closed: Yes · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 34.5 mm · Total length: 165 mm · Thread length: 40.5 mm · Thread length: 50 mm · Height: 5.9 mm · Height: 9.9 mm