Hot 
Reinforced pull pin suitable for the manual Z50 engine of Puch X30 Sport NS / NL, as well as Puch X30 Velux mopeds / mopeds.
&Revised design: The specially developed swivel ball bearing with a contact angle of 60° (shown in figure 3) guarantees durability even under the highest loads. The reinforced clutch springs at the bottom of the accessory can only be used in conjunction with the swivel draw bolt.
Adjusting the clutch: Figure 4 shows the position of the clutch release lever in relation to the abutment and the ball collar nut in relation to the clutch release shaft. This setting results in maximum disengagement with minimum effort. Particular attention must be paid to the play between the decoupling shaft and the conical collar nut, as the clutch bearing will inevitably break within a very short time if the play is too small. With the clutch cable engaged, the free travel on the clutch release lever should be approx. 3 mm.
The angle "A" on the picture is 58°. On the hand lever, these clearances result in a free travel of approx. 1 cm.
Nostalgic product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® revival parts |
| Material | Aluminum, Steel |
| Surface | anodized, blackened |
| Color | red, black |
| Area of application | High End |
| Total length | 35 mm |
| Ø outside | 44.8 mm |
Suitable for the following models
| Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-Gang MS, MV, MV50 3-Gang VSD, DS, VZ, MC |
Accessories & related products
swiing® revival clutch spring 2-disc version (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30.5 mm · Ø outside: 39 mm · Ø wire: 4 mm · Total length: 19.5 mm · Color: gray · Manufacturer: swiing® revival parts · Material: Spring steel · Surface: raw · Number of components: 1 pcs · Area of application: Original · Area of application: Standard
EUR 20,20
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: blue · Surface: coated · Total length: 20.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
EUR 26,80
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: red · Surface: coated · Total length: 23.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
EUR 26,80
HS-Retro drawbar "heavy-duty" Z50 engine 2-slats (1A quality) | Puch Sport, Velux
Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Aluminum · Material: Steel · Color: black · Surface: Hardened · Surface: anodized · Height: 35.2 mm · Ø outside: 44.75 mm · Alternative version of the Puch spare part no.: 050.2.1230.0
EUR 98,40
Moped fans like you also bought:
swiing® revival gasket set Z50 engine | Puch X30 NS / NL
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Sealing paper · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Number of components: 10 pcs · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm
EUR 22,40
Not in stock
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: blue · Surface: coated · Total length: 20.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
EUR 26,80
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: red · Surface: coated · Total length: 23.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
EUR 26,80
Collection only possible with online purchase and appointment.
