Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with a swiing® ingenious EVO or an HPI license plate model 210 (version with light).
Made in Switzerland. Designed for the highest loads and proven in racing.
Installation:
1. Starter pinion: Clean the HPI pole wheel, then screw the counterpart for the cable starter onto the pole wheel (secure the enclosed screws with Loctite).
2. Cable starter: Position the starter housing correctly and tap lightly with a plastic hammer until the cable starter fits perfectly. It can then be screwed into place.
Application:
1. Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
2. Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Other helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber mallet etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Surface | chrome-plated, raw |
| Color | black, Chrome |
| Ignition system | HPI |
| Total length | 160 mm |
| Hole spacing | 137.5 mm |
| Height | 93 mm |
| Ø outside | 130 mm |
| Width | 135 mm |
| Number of fixing points | 2 pcs |
Suitable for the following models
| Puch | E50 |
Accessories & related products
HPI racing ignition 12V with light 60W
Manufacturer: HPI · Material: Aluminum · Material: Steel · Tension: 12 V · Light coil voltage: 12 V · Performance: 60 W · Direction of rotation: left · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Internal flywheel: 61.5 mm · Ø Flywheel outside: 71.5 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 6 pcs · Weight: 340 g · Area of application: Tuning
EUR 346,30
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Area of application: Chemistry · Color: blue · Contents [ml]: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 25,30
EUR 2.530,00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Manufacturer: GPO · Material: Steel · Surface: chrome-plated · Color: Chrome · Chain pitch: 1/2" x 3/16" · Ø outside: 15.9 mm · Number of teeth: 28 pcs · Total length: 257 mm · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
EUR 69,20
Moped fans like you also bought:
Magura gas cable clamp / deco cable clamp Ø 5 x 6 mm
Manufacturer: Magura · Material: Brass · Material: Steel · Surface: nickel-plated · Number of components: 2 pcs · Drive: Slot · Ø Cable bushing: 1.6 mm · Total length: 6 mm · Screw head: Lens head · Thread length: 4 mm · Ø outside: 5 mm · Thread type: M4x0.7 (standard thread)
EUR 2,30
swiing® revival gasket gearbox cover engine 1 mm | Puch E50
Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Number of fixing points: 4 pcs · Thickness: 1 mm · Ø inside: 106 mm · Ø outside: 116 mm · Alternative version of the Puch OEM number: 349.1.10.349.1
EUR 4,50
Collection only possible with online purchase and appointment.
