The Spark EVO Zero Basic module (version 2.0) was developed to make the breaker ignition on your Sachs moped / moped significantly more wear-resistant and low-maintenance.
The box uses the breaker only as a clock generator and replaces the capacitor at the same time. Problems with worn breaker contacts and poor-quality capacitors are therefore a thing of the past. In addition, your ignition coil can build up higher voltages, which has a positive effect on the upper speed limit of heavily tuned motors.
Advantages of the electronic ignition module:
- No wear
- Maintenance-free
- Higher voltage in the upper engine speed range
- Higher engine speeds possible than with conventional contact ignition
- Maintenance-free;
- Easy way to install a cut-off switch or kill switch
Mounting on ignitions with internal ignition coil:
- Mount the box close to the motor, e.g.B. on the motor screw
- Remove the capacitor from your contact ignition
- Remove the ignition coil cable from the capacitor, as well as the cable leading outwards inside your ignition;
- connect the breaker with a new cable and route this to the outside to the first connection of the module
- attach a new cable to the small cable of the ignition coil (e.g. the cable of the ignition coil).B. listed in the accessories) and route this to the outside to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. on the motor screw
Installation for ignition systems with external ignition coil:
- Mount the box close to the external ignition coil, e.g. on the motor screw
- remove the capacitor from your contact ignition
- remove the cable of the pulse coil and the cable leading outwards inside your ignition from the breaker
- connect the breaker with a new cable and lead this outwards to the left-hand connection of the module
- attach a new cable to the pulse coil (e.g. as described in the accessories manual).
- attach a new cable to the pulse coil (as listed in the accessories, for example) and route this outwards to the middle connection of the module
- Also attach the cable that leads to the external ignition coil to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. on the motor screw
- .e.g. on the motor screw
Notes: The breaker gap can be left at 0.4-0.5 mm. Pay attention to the cable routing inside the ignition so that it is not damaged by the rotating flywheel. As before, your light coil supplies 6 V, so there is no need to change your bulbs to 12 V.
You can find more parts for your ignition system on your Sachs moped in the accessories section.
Quality product from the Italian manufacturer SparkEVO.
The set includes the following fixed parts:
Manufacturer: SparkEVO · Height: 33.5 mm, 15.3 mm · Mounting type: Tab for screwing · Connection type: Plug connection · Ø mounting hole: 5.3 mm · Area of application: Tuning
Details
| Manufacturer | SparkEVO |
| Area of application | Tuning |
| Mounting type | Tab for screwing |
| Connection type | Plug connection, Tab for screwing |
| Height | 33.5 mm, 15.3 mm |
| Ø mounting hole | 5.3 mm |
Suitable for the following models
| Sachs |
Accessories & related products
Hot 
Leonelli 6V voltage regulator (1A quality)
Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: raw · Type of current: Alternating current (AC) · Tension: 6 V · Performance: 50 W · Mounting type: Screws · Total length: 50 mm · Width: 27 mm · Height: 15 mm · Ø mounting hole: 6 mm
EUR 33,70
HPI racing ignition 12V with light 60W
Manufacturer: HPI · Material: Aluminum · Material: Steel · Tension: 12 V · Ø cable: 7 mm · Light coil voltage: 12 V · Ø Internal flywheel: 61.5 mm · Performance: 60 W · Direction of rotation: left · Direction of rotation: right · Ø mounting plate: 90 mm · Mounting type: Screws · Ø Flywheel outside: 71.5 mm · Number of fixing points: 6 pcs · Area of application: Tuning · Weight: 340 g
EUR 338,00
swiing® revival cable repair set ignition
Cable cross-section [mm²]: 0.75 mm² · Cable cross-section [mm²]: 1 mm² · Ø single core: 0.15 mm · Number of cables: 2 pcs · Manufacturer: swiing® revival parts · Material: Copper · Material: Plastic · Surface: raw · Ø outside: 1.9 mm · Color: black · Color: yellow · Total length: 300 mm · Area of application: Standard
EUR 10,00
BOSCH Breaker without cable reinforced | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Area of application: Tuning · Cable available: No · Ø Internal flywheel: 90 mm · Ø axle: 4 mm · Number of fixing points: 1 pcs · Ø mounting hole: 4.5 mm · Alternative version of the Pony Spare part no.: A4606 · BOSCH spare part no.: 1 217 013 020 · Alternative version of Sachs spare part no.: 0983 106 000 · BERU spare part no.: 0 340 100 466
EUR 23,60
Hot
VEC electronic ignition coil (replaces ignition coil, capacitor & contact breaker)
Manufacturer: VEC · Ø cable holder: 5 mm · Area of application: Original · Area of application: Performance · Area of application: Standard · Color: black · Total length: 77 mm · Ø Internal flywheel: 90 mm · Place of use: Internal (in the ignition) · Mounting type: Screws · Height: 48 mm · Cable length: 140 mm · Cable length: 420 mm · Number of fixing points: 2 pcs · Hole spacing: 54 mm · Ø mounting hole: 4.6 mm
EUR 112,60
Not in stock
Moped fans like you also bought:
GPO mushroom air filter grille, Bing SRE (Ø=20 mm)
Manufacturer: GPO · Material: Metal · Camouflaged: No · Material: Rubber · Area of application: Tuning · Color: Chrome · Color: black · Filter type: Grille · Ø Internal connection: 20 mm · Length rubber part: 63.5 mm · Length of filter section: 49 mm · Mounting type: Bride · Mounting type: Plug connection clamped · Ø outside: 61 mm · Total length: 113 mm
EUR 14,70
swiing nozzle set M3.5 (54 - 64) Bing SRE, SRA, SRC, SRF
Manufacturer: swiing · Material: Brass · Quantity: 6 pcs · Carburetor type: SRA (1/11/31) Velux · Carburetor type: SRA (1/11/35) Velux · Carburetor type: SRC · Carburetor type: SRE · Carburetor type: SRF · Nozzle type: Main nozzle · Drive: Slot · Total length: 6 mm · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle size: 54 · Nozzle size: 56 · Nozzle size: 58 · Nozzle size: 60 · Nozzle size: 62 · Nozzle size: 64
EUR 17,90
swiing nozzle set M5 (50 - 70) Dell'Orto SHA, PHBG
Manufacturer: swiing · Quantity: 10 pcs · Material: Brass · Carburetor type: PHBG · Carburetor type: SHA (type 3) · Carburetor type: SHA (type 4) · Nozzle type: Main nozzle · Total length: 8 mm · Drive: Slot · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 50 · Nozzle size: 52 · Nozzle size: 55 · Nozzle size: 58 · Nozzle size: 60 · Nozzle size: 62 · Nozzle size: 64 · Nozzle size: 66 · Nozzle size: 68 · Nozzle size: 70
EUR 23,60
NGK BR7EIX Spark plug long thread interference-suppressed Iridium
Manufacturer: NGK · Candle designation: BR7EIX · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning · Candle thread type: long · Spark plug socket: M4 · Thread type: MF14x1.25 (fine pitch thread) · Spark plug socket: SAE · Electrode material: Iridium · Suppressed: Yes · Width across flats SW: 21 mm
EUR 30,30
Hot
VEC electronic ignition coil (replaces ignition coil, capacitor & contact breaker)
Manufacturer: VEC · Ø cable holder: 5 mm · Area of application: Original · Area of application: Performance · Area of application: Standard · Color: black · Total length: 77 mm · Ø Internal flywheel: 90 mm · Place of use: Internal (in the ignition) · Mounting type: Screws · Height: 48 mm · Cable length: 140 mm · Cable length: 420 mm · Number of fixing points: 2 pcs · Hole spacing: 54 mm · Ø mounting hole: 4.6 mm
EUR 112,60
Not in stock
Collection only possible with online purchase and appointment.
