Polini EVO REED engine housing for your Piaggio Ciao, Si, Bravo and Grillo moped / moped.
Most important key points in the ¨overview:
- Intake tract:
The new edition of the legendary Evolution racing gear is used as standard with a supplied side inlet and 4-flap diaphragm. Polini recommends a 21 mm CP (not included) as the ideal carburetor. The air filter for this has been specially adapted to the new engine parts and the 21 mm carburettor.
The rear inlet can be used with a second carburettor if required. A cover plate for closing is included.
The space in the frame for the side intake is limited, but with our test frame, installation was possible without any adjustments. To do this, the engine is moved forwards and backwards in the slots of the frame in order to be able to fit the four screws of the inlet connector. - Cylinder:
With the development of the EVO racing gearbox, a new 47 mm cylinder with four stud bolts was also introduced. The familiar overflow channels and the stud bolt hole pattern from the 43 mm cylinder and the previous 46 mm cylinders are also present in the new housing, which enables operation with these racing cylinders. - Firing:
The racing case is designed for electronic ignitions. Conventional stators with one output for the light can be fitted without any adjustments. However, if stators with three consumer coils are used, adjustments to the housing are required for space reasons.
The Polini ignition (not included in the scope of delivery), which is also a new development, unfortunately does not fit into the tuning housing without adjustments. The cam outlined in the detailed picture must be milled off for this. Machining instructions are included.
If the Polini ignition is used in conjunction with a rotary valve crankshaft, an additional weight must be fitted to compensate for the resulting imbalance. - Crankshaft:
If the gearbox is operated with the side inlet, it is recommended to use the Polini EVO REED full cheek crankshaft (not included in the scope of delivery).
Operation of the crankcase with a standard Piaggio crankshaft is possible and necessary if two carburetors are used.
In addition to the two reinforced C4 SKF ball bearings, the required shim washers and oil seal are also included in the scope of delivery of the crankcase.
The workmanship of the housing is fine. However, there are some small visible brows on the channels, for example, which should be smoothed out a little beforehand.
Details
| Stock number | 6202 |
| Manufacturer | Polini |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
Suitable for the following models
| Piaggio | Ciao - Ciao, Ciao, Ciao, Ciao Si Bravo/Superbravo Grillo |
Accessories & related products
Polini Racing 43 mm cylinder kit incl. head 12 mm KoBo | Piaggio Ciao, Bravo, Boxer
Nominal diameter: 43 mm · Manufacturer: Polini · Material: Gray cast iron · Surface: sandblasted · Displacement: 63 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 45.7 mm · Ø Outlet outside: 22.4 mm · Ø outlet inside: 18.1 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No · Area of application: Tuning
EUR 270,40
Polini EVO Electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Area of application: High End · Area of application: Racing · Area of application: Tuning · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Weight: 554 g · Number of fixing points: 2 pcs · Ø Internal flywheel: 80.5 mm · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 138.5 mm
EUR 563,40
Polini EVO REED crankshaft 12 mm KoBo | Piaggio Ciao, SI, Bravo, Grillo
Manufacturer: Polini · Area of application: High End · Area of application: Racing · Area of application: Tuning · Cheek type: Full cheeks · Material: Steel · Crankshaft stroke: 43 mm · Ø coupling pin / vario pin: 12 mm · Connecting rod length center-center: 87 mm · Thread length: 14 mm · Weight: 784 g · Total length crankpin ignition side: 91.5 mm · Total length crankpin ignition side: 105 mm · Ø crank webs: 70 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Bearing seat right: 15 mm · Thread type: MF10x1.25 (fine pitch thread) · Ø Bearing seat (ignition side): 15 mm · Dimension needle bearing: 12 / 15 x 14.7 mm (axe 12) · Wide crank webs: 32.6 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 44.7 mm · Length 3rd paragraph: 64 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 14.4 mm · Ø 3rd step (on the clutch side): 12 mm · Number of gears: 1 pcs
EUR 326,80
Not in stock
Polini 47 mm cylinder kit EVO 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Area of application: High End · Area of application: Tuning · Material: Gray cast iron · Crankshaft stroke: 43 mm · Displacement: 75 ccm · Ø cylinder neck: 49.8 mm · Camouflaged: No · Ø Outlet outside: 22 mm · Ø Outlet outside: 27 mm · Nominal diameter: 47 mm · Number of fixing points: 4 pcs · Ø piston pin (B): 12 mm · Hole pattern [mm]: 43 x 52 · Decompressor: Yes · Hole spacing outlet: 23 mm · Hole spacing outlet: 38 mm · Thread outlet: M5x0.8 (standard thread)
EUR 315,50
Polini 46 mm cylinder kit aluminum | Peugeot 103, SPX50, 104, 105, GL 10
Manufacturer: Polini · Material: Aluminum · Displacement: 65 ccm · Ø cylinder neck: 50 mm · Camouflaged: No · Ø Outlet outside: 25 mm · Nominal diameter: 46 mm · Number of fixing points: 4 pcs · Ø piston pin (B): 7 mm · Hole pattern [mm]: 45.4 x 50.5 · Decompressor: Yes · Hole spacing outlet: 50 mm · Outlet type: slanted · Thread outlet: M7x1 (standard thread)
EUR 259,10
Polini CP 21 mm carburetor & air filter (hand choke) | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Area of application: Racing · Area of application: Tuning · Material: Aluminum · Carburetor type: CP · Total length: 71 mm · Width: 66 mm · Camouflaged: No · Nominal diameter: 21 mm · Height: 122 mm · Ø Inside entrance: 42 mm · Mounting type: Rubber sleeve · Ø Output inside: 22.5 mm · Ø Air filter connection: 47 mm · Ø fuel hose connection: 6 mm · Ø fuel hose connection: 7 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Nozzle thread: M5 · Nozzle block: 35-12 · Nozzle size: 82 · Nozzle size: 84 · Nozzle size: 86 · Size of secondary nozzle: 40
EUR 191,50
Moped fans like you also bought:
NGK B8ES spark plug long thread
Manufacturer: NGK · Candle designation: B8ES · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Candle thread type: long · Spark plug socket: M4 · Spark plug socket: SAE · Suppressed: No · Width across flats SW: 21 mm · Thread type: MF14x1.25 (fine pitch thread)
EUR 7,30
NGK B7ES spark plug long thread
Manufacturer: NGK · Candle designation: B7ES · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Candle thread type: long · Spark plug socket: M4 · Spark plug socket: SAE · Suppressed: No · Width across flats SW: 21 mm · Thread type: MF14x1.25 (fine pitch thread)
EUR 7,30
Polini EVO Electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Area of application: High End · Area of application: Racing · Area of application: Tuning · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Weight: 554 g · Number of fixing points: 2 pcs · Ø Internal flywheel: 80.5 mm · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 138.5 mm
EUR 563,40
Polini EVO REED crankshaft 12 mm KoBo | Piaggio Ciao, SI, Bravo, Grillo
Manufacturer: Polini · Area of application: High End · Area of application: Racing · Area of application: Tuning · Cheek type: Full cheeks · Material: Steel · Crankshaft stroke: 43 mm · Ø coupling pin / vario pin: 12 mm · Connecting rod length center-center: 87 mm · Thread length: 14 mm · Weight: 784 g · Total length crankpin ignition side: 91.5 mm · Total length crankpin ignition side: 105 mm · Ø crank webs: 70 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Bearing seat right: 15 mm · Thread type: MF10x1.25 (fine pitch thread) · Ø Bearing seat (ignition side): 15 mm · Dimension needle bearing: 12 / 15 x 14.7 mm (axe 12) · Wide crank webs: 32.6 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 44.7 mm · Length 3rd paragraph: 64 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 14.4 mm · Ø 3rd step (on the clutch side): 12 mm · Number of gears: 1 pcs
EUR 326,80
Not in stock
Polini 47 mm cylinder kit EVO 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Area of application: High End · Area of application: Tuning · Material: Gray cast iron · Crankshaft stroke: 43 mm · Displacement: 75 ccm · Ø cylinder neck: 49.8 mm · Camouflaged: No · Ø Outlet outside: 22 mm · Ø Outlet outside: 27 mm · Nominal diameter: 47 mm · Number of fixing points: 4 pcs · Ø piston pin (B): 12 mm · Hole pattern [mm]: 43 x 52 · Decompressor: Yes · Hole spacing outlet: 23 mm · Hole spacing outlet: 38 mm · Thread outlet: M5x0.8 (standard thread)
EUR 315,50
Collection only possible with online purchase and appointment.
