Reinforced pull pin suitable for the manually shifted Z50 engine of Puch X30 Sport mopeds / mopeds, which have a special clutch with 3 plates.
This is often the case with kickstarter engines.
Revised design: The specially developed angular contact ball bearing with a contact angle of 60° (shown in Figure 3) guarantees durability even under the highest loads. The reinforced clutch springs at the bottom of the accessory can only be used in conjunction with the swivel pull pin.
Adjusting the clutch: Figure 4 shows the position of the clutch release lever in relation to the abutment and the ball collar nut in relation to the clutch release shaft. This setting results in maximum disengagement with minimum effort. Particular attention must be paid to the play between the decoupling shaft and the conical collar nut, as the clutch bearing will inevitably break within a very short time if the play is too small. With the clutch cable engaged, the free travel on the clutch release lever should be approx. 3 mm.
The angle "A" on the picture is 58°. On the hand lever, these clearances result in a free travel of approx. 1 cm.
Nostalgic product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® revival parts |
| Material | Aluminum, Steel |
| Surface | anodized, blackened |
| Color | red, black |
| Ø outside | 44.7 mm |
| Total length | 34.9 mm |
| Area of application | High End |
Suitable for the following models
| Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-Gang MS, MV, MV50 3-Gang VSD, DS, VZ, MC |
Accessories & related products
swiing® revival clutch spring 2-disc version (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4 mm · Manufacturer: swiing® revival parts · Total length: 19.5 mm · Area of application: Original · Area of application: Standard · Material: Spring steel · Color: gray · Surface: raw · Number of components: 1 pcs · Ø inside: 30.5 mm · Ø outside: 39 mm
EUR 21,00
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Area of application: Tuning · Color: blue · Ø outside: 39 mm · Ø inside: 30 mm · Total length: 20.5 mm
EUR 27,90
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Area of application: Tuning · Color: red · Ø outside: 39 mm · Ø inside: 30 mm · Total length: 23.5 mm
EUR 27,90
Moped fans like you also bought:
Motorex engine oil (gear oil) manual 450 ml
Temperature resistance (min.): -30 - 220 °C · Manufacturer: Motorex · Viscosity (SAE): 80W · Oil type: GL4 · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Area of application: Gearbox lubrication with clutch
EUR 11,60
EUR 25,78/l
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Area of application: Tuning · Color: red · Ø outside: 39 mm · Ø inside: 30 mm · Total length: 23.5 mm
EUR 27,90
Collection only possible with online purchase and appointment.
