Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an original Bosch / Ducati ignition.
Made in Switzerland. Designed for the highest loads and proven in racing.
Fitting:
1. Starter pinion: Clean the flywheel, then screw the counterpart for the cable starter onto the pole wheel (secure with Loctite).
2. Pull-wire starter: Position the starter housing correctly and tap lightly with a plastic hammer until the pull-wire starter is perfectly seated. It can then be screwed into place.
Application:
1. Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
2. Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Other helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber mallet etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
Details
Width | 150 mm |
Ø outside | 130 mm |
Height | 88 mm |
Manufacturer | swiing® ingenious parts |
Material | Steel, Plastic |
Surface | chrome-plated |
Color | Chrome, black-matt |
Ignition system | BOSCH, DUCATI |
Total length | 160 mm |
Hole spacing | 137.5 mm |
Number of fixing points | 2 pcs |
Suitable for the following models
Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Area of application: Chemistry · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Contents [ml]: 10 ml · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 24,70
EUR 2.470,00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Manufacturer: GPO · Color: Chrome · Material: Steel · Surface: chrome-plated · Chain pitch: 1/2" x 3/16" · Ø outside: 15.9 mm · Number of teeth: 28 pcs · Total length: 257 mm · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
EUR 67,50
IXS motorcycle gloves Skull S black
Manufacturer: IXS · Test mark: EN13594:2015 · Material: Polyester (PES) · Color: black · Color: white · Gender: Unisex · Size: L · Size: S · Hand circumference: 21 - 22 cm · Hand circumference: 22 - 23 cm · Hand circumference: 23 - 24 cm · Hand circumference: 24 - 25 cm
EUR 47,10
Moped fans like you also bought:
Airsal 44 mm cylinder kit 65 ccm camouflaged | Puch
Nominal diameter: 44 mm · Manufacturer: Airsal · Material: Aluminum · Surface: sandblasted · Displacement: 65 ccm · Crankshaft stroke: 43 mm · Hole spacing inlet: 38 mm · Ø cylinder neck: 48 mm · Ø outlet inside: 25 mm · Area of application: Tuning · Inlet window: 24 / 20 x 15 · Hole spacing outlet: 42 mm · Thread inlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Ø piston pin (B): 12 mm · Outlet type: straight · Thread outlet: M6x1 (standard thread) · Number of fixing points: 4 pcs · Decompressor: Yes · Camouflaged: Yes
EUR 95,70
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø Stranded wire: 1.25 mm · Ø nipple: 3 mm · Nipple length: 5 mm · Manufacturer: Made in Germany · Number of components: 1 pcs · Material: Steel · Surface: blue galvanized · Nipple shape: Cylinder · Area of application: Standard · Cable length: 2200 mm
EUR 3,15
Magura gas cable clamp / deco cable clamp Ø 5 x 6 mm
Ø Cable bushing: 1.6 mm · Manufacturer: Magura · Number of components: 2 pcs · Material: Brass · Material: Steel · Surface: nickel-plated · Thread type: M4x0.7 (standard thread) · Ø outside: 5 mm · Drive: Slot · Screw head: Lens head · Thread length: 4 mm · Total length: 6 mm
EUR 2,25
Motorex Automatic Motor Oil (ATF) 450 ml
Manufacturer: Motorex · Temperature resistance (min.): -45 - 200 °C · Contents [ml]: 450 ml · Gearbox type: Automatic machine · Area of application: Gearbox lubrication with clutch · Pony spare part no.: A2080 · Sachs spare part no.: 0263 014 002
EUR 11,20
EUR 24,89/l
GPO 44 mm cylinder head tuning | Puch Maxi S, N / X30 NS, NL, N-2AH
Width: 125 mm · Height: 55 mm · Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Ø cylinder: 44 mm · Area of application: Tuning · Candle thread: short · Hole pattern [mm]: 44 x 44 · Total length: 135 mm · Number of fixing points: 4 pcs · Decompressor: No · Camouflaged: Yes
EUR 48,40