Rear light "Iowa" chrome

Leonelli 12V voltage regulator (1A quality)

Width: 27 mm · Height: 15 mm · Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: blue galvanized · Tension: 12 V · Type of current: Alternating current (AC) · Performance: 100 W · Ø mounting hole: 6 mm · Mounting type: Screws · Total length: 50 mm

GPO light coil 6/12V - 15/25W

Height: 22 mm · Manufacturer: GPO · Ø Internal flywheel: 90 mm · Tension: 6 V · Tension: 12 V · Performance: 15 W · Performance: 25 W · Area of application: Standard · Ø mounting hole: 4.7 mm · Mounting type: Screws · Total length: 76.5 mm · Hole spacing: 55 mm · Number of fixing points: 2 pcs · Alternative version of the Pony Spare part no.: A2110 · Alternative version of Sachs spare part no.: 0265 113 004

NSK BO15 shoulder ball bearing 15/40/10 (A4502)

Bearing type: Shoulder bearing · Bearing cage: Brass cage ball-guided · Stock number: BO15 · Inner ring width: 10 mm · Manufacturer: NSK · Material: Brass · Material: Steel · Area of application: Standard · Surface: blank · Width: 10 mm · Ø outside: 40 mm · Ø inside: 15 mm · Ball bearing closed: No · Pony spare part no.: A4502 · Sachs spare part no.: 0932 007 001

NSK 6201 ball bearing 12/32/10

Bearing cage: "-" Sheet steel cage ball-guided · Ø inside: 12 mm · Stock number: 6201 · Inner ring width: 10 mm · Manufacturer: NSK · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Area of application: Standard · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 10 mm · Ø outside: 32 mm · Ball bearing closed: No

Oil seal NBR 14.96x31.5x3.5 Pinion shaft | Sachs 502, 50/2, 503 (A1134)

Ø inside: 14.96 mm · Manufacturer: Sachs · Material: NBR · Area of application: Standard · Surface: coated · Place of use: Pinion shaft · Width: 3.5 mm · Ø outside: 31.5 mm · Temperature resistance (min.): -30 - 100 °C · Pony spare part no.: A1134 · Sachs spare part no.: 0230 011 100 · Sachs spare part no.: 0230 011 200

NTN 608 Ball bearing 8/22/7

Bearing type: Deep groove ball bearing · Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 608 · Inner ring width: 7 mm · Manufacturer: NTN · Bearing clearance: CN (standard) · Width: 7 mm · Ø outside: 22 mm · Ø inside: 8 mm

Oil seal NBR 15/30/5.5 A crankshaft | Sachs (A4215 & A5602)

Temperature resistance (min.): -30 - 100 °C · Simmering type: A - With rubberized outer part / one sealing lip. · Manufacturer: Sachs · Material: NBR · Surface: rubberized · Width: 5.5 mm · Ø outside: 30 mm · Place of use: Crankshaft · Ø inside: 15 mm · Pony spare part no.: A5602 · Sachs spare part no.: 0230 111 100

swiing® ingenious wheel axle spoke hub front Ø 29 mm conversion kit with ball bearings | Puch

Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Manufacturer: swiing® ingenious parts · Ø inside: 12 mm · Material: Steel · Surface: blue galvanized · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29.02 mm · Ø shaft: 11.95 mm · Width across flats SW: 19 mm · Thread length: 40.5 mm · Thread length: 50 mm · Shank length: 74.5 mm · Total length: 165 mm · Ball bearing closed: Yes

Oil seal NBR 15/30/7 B DUO | Sachs 50/2 / 503 (A1830)

Temperature resistance (min.): -30 - 100 °C · Simmering type: B DUO - With sheet metal outer casing / two sealing lips. · Manufacturer: Sachs · Material: NBR · Width: 7 mm · Ø outside: 30 mm · Ø inside: 15 mm · Pony spare part no.: A1830 · Sachs spare part no.: 0250 090 000

swiing® revival gasket set | Sachs 503 AB, AC wide wall

Manufacturer: swiing® revival parts · Area of application: Standard · Material: Aluminum · Material: Copper · Material: Rubber · Material: Sealing carton · Material: Sealing paper · Ø outlet inside: 24 mm · Number of components: 21 pcs · Hole pattern [mm]: 56 x 56 · Hole spacing outlet: 38.5 mm

Engine revision set | Sachs 503 AB CH

Manufacturer: NSK · Manufacturer: NTN · Area of application: Standard

GPO sprocket 9 - 21 teeth wide | Puch

Chain pitch: 1/2" x 3/16" · Chain type: 415H · Manufacturer: GPO · Material: Steel · Surface: Hardened · Number of teeth: 9 pcs · Number of teeth: 10 pcs · Number of teeth: 11 pcs · Number of teeth: 12 pcs · Number of teeth: 13 pcs · Number of teeth: 14 pcs · Number of teeth: 15 pcs · Number of teeth: 16 pcs · Number of teeth: 17 pcs · Number of teeth: 18 pcs · Number of teeth: 19 pcs · Number of teeth: 20 pcs · Number of teeth: 21 pcs · Recording type: Interlocking · Total thickness: 4.6 mm