High-quality full cheek crankshaft for Morini M0, M01 and M1 engines which is installed on Alpa Turbo / Chopper and Malaguti Fifty mopeds, among others.
The connecting rod is highly polished. In addition, the rear connecting rod bearing is a silver bearing, which has excellent emergency running properties. The balancing bores of the racing crankshaft are sealed with aluminum inserts for greater pre-compression.
Note: The crankshaft does not fit FMT1 CH engines.
Corresponding bearings, oil seals, racing cylinders etc. can be found in the accessories section.
Branded product from the Portuguese manufacturer Jasil under the Top Racing brand.
Details
Manufacturer | Jasil |
Cheek type | Full cheeks |
Crankshaft stroke | 39 mm |
Total length of crankpin on clutch side | 71 mm |
Total length crankpin ignition side | 67.25 mm |
Area of application | Racing |
Ø piston pin (B) | 12 mm |
Ø Bearing seat (clutch side) | 17 mm |
Ø Bearing seat (ignition side) | 17 mm |
Suitable for the following models
Alpa Chopper / Turbo | |
Malaguti |
Accessories & related products
Airsal 43.5 mm cylinder kit 12 mm KoBo | Morini
Nominal diameter: 43.5 mm · Manufacturer: Airsal · Material: Cast aluminum · Camouflaged: No · Area of application: Tuning · Surface: sandblasted · Ø piston pin (B): 12 mm · Ø cylinder neck: 47.9 mm · Ø outlet inside: 23.2 mm · Hole spacing outlet: 35 mm · Decompressor: No · Outlet type: straight · Thread outlet: M5x0.8 (standard thread) · Number of fixing points: 4 pcs · Hole pattern [mm]: 46 x 46
EUR 112,60
Moped fans like you also bought:
Magura cable clamp Ø 8 x 15 mm
Thread type: M6x1 (standard thread) · Manufacturer: Magura · Total length: 15 mm · Area of application: Standard · Material: Brass · Material: Steel · Surface: blue galvanized · Surface: nickel-plated · Ø Cable bushing: 2.3 mm · Drive: External hexagon · Drive: Slot · Thread length: 7 mm · Screw head: Hexagon · Width across flats SW: 7 mm · Ø outside: 8 mm · Ø Bundle: 6 mm
EUR 2,80
swiing® revival snap ring low control bearing set (version 2.0)
Manufacturer: swiing® revival parts · Thickness: 0.6 mm · Material: Spring steel · Surface: blank · Nominal diameter: 20 mm · Nominal diameter: 28 mm · Height: 7 mm · Puch spare part no.: 349.1.30.015.1 · Sachs spare part no.: P0521
EUR 2,80
Magura adjusting screw brake long
Thread type: MF6x0.75 (fine pitch thread) · Manufacturer: Magura · Total length: 47 mm · Total length: 65 mm · Material: Brass · Surface: nickel-plated · Ø shaft: 6 mm · Shank length: 11 mm · Drive: Knurled screw · Thread length: 24 mm · Ø External head: 9.1 mm · Color: silver
EUR 4,40
NTN 6203 C3 Ball bearing 17/40/12
Bearing type: Deep groove ball bearing · Inner ring width: 12 mm · Manufacturer: NTN · Bearing clearance: C3 · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Material: Steel · Surface: blank · Ø inside: 17 mm · Ø outside: 40 mm · Width: 12 mm · Stock number: 6203 · Area of application: Standard · Ball bearing closed: No
EUR 10,00
Oil level screw engine | Zündapp Bergsteiger / Alpa Chopper / Malaguti Fifty
Manufacturer: ALPA · Area of application: Standard · Material: Steel · Surface: blue galvanized · Color: silver · Thread type: M6x1 (standard thread) · Drive: Slot · Screw head: Cylinder head · Thread length: 16 mm · Number of components: 1 pcs
EUR 2,70